PTFE Sheets Manufacturer, Supplier & Exporter in Bharuch, Gujarat
National Fluoromers manufactures PTFE Sheets at its own plant in MIDC Miraj and supplies them to process plants, OEMs and fabricators in Bharuch, Gujarat. We make moulded, skived, chemically etched and dimpled sheets in virgin PTFE and filled grades.
Buyers in and around Jhagadia GIDC, Dahej, Ankleshwar, Panoli and Vilayat use our sheets for gaskets, tank linings, slide pads, electrical insulation and bridge bearings. We dispatch to Bharuch from our Miraj plant through road transport and courier partners.
- Pan-Indiaroad and courier dispatch
- Directfrom the manufacturer
- Since 2007PTFE manufacturing
PTFE Sheets range we supply in Bharuch
Compression-moulded and sintered sheets up to 100 mm thick and 1200 × 1200 mm. Dense and dimensionally stable, so they suit heavy-duty gaskets, insulators, wear pads and structural supports.
Thin, flexible sheets skived from a sintered billet, from 0.1 mm up to 3 mm thick and up to 1200 mm wide, in rolls or cut lengths. Used for electrical insulation, diaphragms, linings and thin gaskets.
Sheets etched on one or both sides (0.5 mm to 100 mm) so they can be bonded to steel, rubber or composites. The right choice for lined tanks, bonded bearing pads and laminated seals.
Precision-moulded dimpled sheets, 3 mm to 8 mm thick, made to IRC 83 for POT-PTFE and sliding bridge bearings. The dimples hold silicone grease and keep friction at about 0.04 to 0.06.
Sheets slit into strips and films for guide strips, wear strips, insulation tapes and sealing in tight spaces. Available plain, etched or bronze and carbon filled.
Sheets in glass, carbon, graphite, bronze and MoS₂ filled grades where you need better wear resistance, lower creep or higher load capacity than virgin PTFE gives.
technical specifications
| Property | Value |
|---|---|
| Material | Virgin PTFE / all filled grades |
| Moulded sheet thickness | Up to 100 mm |
| Moulded sheet size | Up to 1200 mm × 1200 mm |
| Skived sheet thickness | 0.1 mm to 3 mm |
| Skived sheet width | Up to 1200 mm, rolls or cut lengths |
| Etched sheet | One side / both sides, 0.5 mm to 100 mm |
| Dimple sheet | 3 mm to 8 mm, as per IRC 83 |
| Density | 2.1 to 2.2 g/cm³ |
| Working temperature | -200°C to +260°C |
| Sizes | Standard and non-standard, cut to size |
PTFE Sheets for industries in Bharuch
Bharuch district is one of India's densest chemical regions, covering Jhagadia, Dahej, Ankleshwar, Panoli and Vilayat, with fertiliser, petrochemical and pharma plants alongside.
- Chemicals and specialty chemicals: Customers in Jhagadia and Vilayat rely on us for flange gaskets and bonded linings in tanks, columns and scrubbers.
- Oil, gas and petrochemicals: Buyers in Dahej source gaskets, slide plates under pipe racks and corrosion-proof linings from us.
- Fertilisers: We supply acid-resistant gaskets and linings in urea, ammonia and sulphuric acid plants to plants in Bharuch.
- Pharma and biotech: Buyers in Jhagadia and Panoli source FDA-grade gaskets and liners in reactors, dryers and filter housings from us.
- Water and effluent treatment: We supply gaskets and liners in chlorine dosing and chemical dosing systems to plants in Bharuch district.
applications of PTFE Sheets
- Gaskets and seals: Ready-cut and fabricated gaskets for chemical pipelines, flanges, reactors and pumps.
- Tank and duct linings: Etched sheets bonded inside tanks, chutes and ducts that handle acids and solvents.
- Sliding and wear pads: Slide pads, shims, wear strips and machine slideway linings where low friction matters.
- Electrical insulation: Skived sheets as insulation layers in transformers, switchgear and cable wrapping.
- Bridge and structural bearings: Dimpled and plain sheets for POT-PTFE bearings, sliding plates and expansion joints.
- Food and pharma equipment: Virgin, non-toxic sheets for gaskets, liners and release surfaces in contact parts.
why buyers in Bharuch choose National Fluoromers
- Own manufacturing since 2007: Moulding, sintering and CNC machining happen at our plant in MIDC Miraj, so you buy direct from the maker, not a trader.
- Virgin and filled grades: Virgin PTFE plus glass, carbon, graphite, bronze and MoS₂ filled grades for the same product.
- Custom sizes: Standard and non-standard sizes, cut-to-size pieces and machined parts made to your drawing.
- Reliable supply to Bharuch: We pack sheets flat and rods, bushes and parts in cartons so they arrive undamaged, and keep you updated on dispatch.
- Quality checks: Every batch is checked for dimensions, density and surface finish before dispatch.
FAQs: PTFE Sheets in Bharuch
Call +91-7620544880 or email sales@nationalptfe.net
Send Enquiry
